SHOP NOW
PRODUCTS
ESCON 70/10, 4-Q Servo controller for DC/EC motors
MODEL: AE - MX422969
SGD $ 890.00
Pre-Order
In Bulk
(per piece)
(per piece)
ESCON 70/10, 4-Q Servo controller for DC/EC motors, 10/30 A, 10 - 70 VDC
The ESCON 70/10 is a small-sized, powerful 4-quadrant PWM servo controller for the highly efficient control of permanent magnet-activated brushed DC motors or brushless EC motors up to approximately 700 Watts.
PRODUCT | |
Weight | 259 g |
MOTOR | |
DC motors up to | 700 W |
EC motors up to | 700 W |
SENSOR | |
Without sensor (DC motors) | Yes |
DC tacho | Yes |
Digital incremental encoder (2-channel, single-ended) | Yes |
Digital incremental encoder (2-channel, differential) | Yes |
Digital incremental encoder (3-channel, differential) | Yes |
Digital Hall sensors (EC Motors) | Yes |
OPERATING MODES | |
Current controller | Yes |
Speed controller (open loop) | Yes |
Speed controller (closed loop) | Yes |
ELECTRICAL DATA | |
Operating voltage Vcc (min.) | 10 V |
Operating voltage Vcc (max.) | 70 V |
Max. output voltage (factor * Vcc) | 0.95 |
Max. output current Imax | 30 A |
Max. time of peak output current Imax | 20 s |
Continuous output current Icont | 10 A |
PWM clock frequency of power stage | 53.6 kHz |
Sampling rate PI current controller | 53.6 kHz |
Sampling rate PI speed controller | 5.36 kHz |
Max. efficiency | 98 % |
Max. speed (DC) | 150000 rpm |
Max. speed (EC; 1 pole pair) block commutation | 150000 rpm |
Built-in motor choke per phase | 15 µH |
INPUTS | |
Hall sensor signals | H1, H2, H3 |
Encoder signals | A, A, B, B\ |
Max. encoder input frequency | 1 MHz |
Digital inputs | 2 |
Functionality of digital inputs | Enable, enable CW, enable CCW, enable CW+CCW, enable + direction of rotation, stop, PWM set value, RC Servo set value, fixed set value |
Analog inputs | 2 |
Resolution, range, circuit | 12-bit, -10…+10V, differential |
Functionality of analog inputs | Set value, current limit, offset, speed ramp |
Potentiometers | 2 |
Functionality of the potentiometers | set value, current limit, offset, speed ramp, gain, IxR factor |
OUTPUTS | |
Digital outputs | 2 |
Functionality of digital outputs | ready, speed comparator, current comparator, commutation frequency |
Analog outputs | 2 |
Resolution, range | 12-bit, -4…+4V |
Functionality of analog outputs | current monitor,speed monitor, temperature, fixed value |
VOLTAGE OUTPUTS | |
Hall sensor supply voltage | +5 VDC, max. 30 mA |
Encoder supply voltage | +5 VDC, max. 70 mA |
Auxiliary output voltage | +5 VDC, max. 10 mA |
INTERFACE | |
USB 2.0 (full speed) | Yes |
DISPLAY | |
Status indicator "Ready" | green LED |
Status indicator "Error" | red LED |
PROTECTIVE FUNCTIONS | |
Protective functions | current limit, overcurrent, excess temperature, undervoltage, overvoltage, voltage transients, short-circuits in the motor cable |
AMBIENT CONDITIONS | |
Temperature – Operation (min.) | -30 °C |
Temperature – Operation (max.) | 45 °C |
Temperature – Extended Range | +45…+82°C, Derating: -0.27 A/°C |
Temperature – Storage (min.) | -40 °C |
Temperature – Storage (max.) | 85 °C |
Humidity (non-condensing) (min.) | 5 % |
Humidity (non-condensing) (max.) | 90 % |
MECHANICAL DATA | |
Weight | 259 g |
Dimension (length) | 125 mm |
Dimension (width) | 78.5 mm |
Dimension (height) | 27 mm |
Mounting | Flange for M4 screws |
SOFTWARE | |
Installation program | ESCON Setup |
Graphical User Interface | ESCON Studio |
Operating system | Windows 10, 8, 7, Windows XP SP3 |