Layer-7.png
SHOP NOW

PRODUCTS

100:1 Micro Metal Gearmotor MP 6V

100:1 Micro Metal Gearmotor MP 6V

MODEL: 2367

SGD $ 31.50
Pre-Order
In Bulk
(per piece)

This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.

Key specifications:

voltage no-load performance stall extrapolation
6 V 220 RPM, 70 mA 0.94 kg⋅cm (13 oz⋅in), 0.67 A

 

These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.

The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).

 

 

Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our encoders for micro metal gearmotors (see the picture on the right), to provide motor speed or position feedback.

With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change.

Please see the micro metal gearmotor datasheet (2MB pdf) for more information, including detailed performance graphs for each micro metal gearmotor version. 

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg-cm (35 oz-in) for the 380:1 and 1000:1 gearboxes, and 2 kg-cm (25 oz-in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Details for item #2367

Exact gear ratio: 35×37×35×38÷12×11×13×10100.37:1

This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.

Key specifications:

voltage no-load performance stall extrapolation
6 V 220 RPM, 70 mA 0.94 kg⋅cm (13 oz⋅in), 0.67 A

Gearmotor Dimensions

In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.

Dimensions of versions with carbon brushes (HPCB)

 

Dimensions of the Pololu micro metal gearmotors with carbon brushes (HPCB). Units are mm over [inches].

 

Dimensions of versions with precious metal brushes (LP, MP, and HP)

 

Dimensions of the Pololu micro metal gearmotors with precious metal brushes: low-power (LP), medium-power (MP), and high-power (HP). Units are mm over [inches].

 

These diagrams are also available as a downloadable PDF (262k pdf).

Dimensions

Size: 10 × 12 × 26 mm1
Weight: 9.5 g
Shaft diameter: 3 mm2

General specifications

Gear ratio: 100.37:1
No-load speed @ 6V: 220 rpm3
No-load current @ 6V: 0.07 A4
Stall current @ 6V: 0.67 A
Stall torque @ 6V: 0.94 kg·cm
Max output power @ 6V: 0.50 W
Extended motor shaft?: N
Motor type: 0.67A stall @ 6V (MP 6V)

Performance at maximum efficiency

Max efficiency @ 6V: 33 %
Speed at max efficiency: 170 rpm
Torque at max efficiency: 0.19 kg·cm
Current at max efficiency: 0.17 A
Output power at max efficiency: 0.32 W

Notes:

  1. Output shaft adds 9 mm to the 26 mm length.
  2. D shaft.
  3. Typical; ±20%.
  4. Typical, ±50%; no-load current depends on internal friction, which is affected by many factors, including ambient temperature and duration of motor operation.